Heath Heathkit SA-2060A Manuals & User Guides. User Manuals, Guides and Specifications for your Heath Heathkit SA-2060A TV Antenna. Database contains 1 Heath Heathkit SA-2060A Manuals (available for free online viewing or downloading in PDF): Manual. I recently put on line a second Heath model SA-2060 antenna tuner into my station, and was reminded that several had asked me about an earlier post wherein I described the SA-2060 as having a 3 position antenna switch that performed, as follows: 1. Bypass tuner so as to feed radio direct to antennas 2.
HEATHKIT. MANUAL for the. DELUXE. ANTENNA TUNER. Model SAA You must deliver the unit at your expense to the Heath factory, any Heathkit. View and Download Heath Kit SAA manual online. Heathkit SAA TV Antenna pdf manual download. Antenna Tuner SA Amateur-D Heathkit Brand, Heath Co.; Benton Harbor Select picture or schematic to display from thumbnails on the right and click for.
| Author: | Goltigor Dinos |
| Country: | Mongolia |
| Language: | English (Spanish) |
| Genre: | Education |
| Published (Last): | 8 August 2008 |
| Pages: | 68 |
| PDF File Size: | 17.22 Mb |
| ePub File Size: | 7.73 Mb |
| ISBN: | 648-9-92013-203-9 |
| Downloads: | 93438 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Mosar |
This will make the top edge of the ceramic in- sulator plate flush with the top edge of the capacitor rear plate.
Then, while holding the strap forward, tighten the strap mounting screw at C2 hole AR. A voltage sampled directly from heeathkit transmission line is summed with the voltage at L Hold the leads so they cannot fly toward your eyes. Tighten the screw only finger tight. Mount a capacitor mounting bracket to the rear inductor end plate and the remaining spacers at BM and BN.
You can adjust it to sa-260 out load reactance and trans- form the load impedance to the required ohm transmitter or amplifier output impedance. Connect the hook on the free end of the spiral shield to solder lug K NS. Meter Ranges Forward 2 ranges Low — watts.
Tighten the mounting screws at Hheathkit, F, G, and H. Do not overtighten the hardware. Please do not send parts for testing, unless this is specifi- cally requested by our Consultants.
When you are instructed to mount these plates to a capacitor plate, as in the next step, be sure you position the side with the raised area toward the capacitor plate. The REF meter will indicate sa2060 reflected power on the scale.
Any part that is packed in an individual envelope with heathkif part number on it should be placed back in the envelope after you identify it until all the parts are accounted for. Make sure you wrap the tape so it will overlap part of the tape ends already wrapped around the cores.
With a single switch you may select a dummy load, or any of three permanently-connected antennas, in- cluding a long-wire hheathkit. Output Impedance Wide range. Position the two contactor springs toward the ends of the tension rod.
Heath kit SA-2060A Manual
Repeat steps 4 and 5 until you have 26 rotor plates and 25 large spacers installed on the shaft. Be sure to record the settings of both variable capacitor knobs and the counter so you can preset the controls the next time you use a particular band. Turn the rotors of both matching capacitors to their fully-meshed positions. This is the type we have supplied with the parts. During the tuning procedure, apply only enough RF power from the exciter to get a meaningful reading on REF meter Ml in its most sensitive position.
Refer to Detail A and temporarily remove the outer nut from feedthrough J3. Push the spring down and insert the tab of the spring into hole AP in the capacitor rear plate. Secure the strap at AN with a nut. Then tightly twist the wire ends and add a small amount of solder to hold the fine strands together.
Refer to the inset drawing on the Pictorial and be sure SW rotor is positioned exactly as shown. Page 52 Heathkit Coaxial-Fed Antennae An antenna fed with a coaxial line, such as a beam antenna or a center fed dipoie, can easily be matched with your Antenna Tuner to provide a good match to the transmitter across the entire band.
HEATH KIT SAA MANUAL Pdf Download.
Where differences exist between the basic operation of the two circuits, further details will be supplied. This completes the assembly of the matching capacitor. Secure the detent with a control flat washer and a control nut tighten the hardware. Start one end of the prepared tension rod into hole BD in the front inductor end plate. Position the end of the remaining strap coming from the rear of inductor Ll onto the threaded spacer at AT on capacitor Cl.
Detail B Slide the inductor rearward and line up its mounting holes with those in the chassis, Hold the inductor in place.
Heathkit SA A Deluxe Antenna Tuner (+ Parts + Schem.) (manual)
Set the rear inductor end plate aside temporarily. Switches the output to a dummy load, or to any of three coaxial feediines.
The illustrations in the Manual are called Picto- rials and Details. Use enough solder and heat to assure a good con- nection on all six leads and wires at the solder lug.
Then install the setscrew in hole AS. If you are unable to locate an order form, write us a letter or card including: Keep the “Illustration Booklet” with the As- sembly Manual. Start the free end of the tension rod into hole BL in the rear inductor end plate. If necessary, after the screw is tight, reform the straps slightly to make sure they are as far as possible from the inductor spacer screws at the upper corners.
Refer to Detail B and loosen the setscrew in the counter shaft stepped coupler. Turn the screw in until the unslotted end is flush with the other side of the plate. Also include switch positions, connections to other units, operating procedures, voltage readings t and any other infor- mation you think might be helpful.
Be sure the small holes in the strap line up with the corresponding hole in the inductor end plate before you tighten the hardware. Use diagonal cutters or scissors. With a very good load, one with less than 1. Place a flat washer, the male heathoit element, and a fiber washer on the stud.
Heathkit Sa 2040 Tuner Manual
Antenna Tuner SA-2060
Sa 2060a
Cut the indicated lug of the terminal strip in half as shown. Connect this ground post to a good earth ground or a hdathkit pipe. Push the stepped coupler all the way onto the shaft of the counter before you tighten the setscrew. Avoid eye injury when you cut off excessive lead lengths.